The house is cold, the thermostat says it is calling for heat, and the furnace is either silent or running in short, frustrating bursts. If you are searching for furnace repair in Orem, you probably want two things at once: a warm house tonight and an honest explanation of what went wrong. This guide covers the most common reasons a furnace stops heating, which checks are safe for a homeowner, and when the problem belongs to a technician.
Valley Plumbing, Heating, and Cooling provides furnace repair for homes in Orem and across its Utah service area, so the steps below follow the same order a technician would use when diagnosing a furnace that has stopped working.
Start with the simple checks before you call
Some furnace problems are not furnace problems at all. Before you pick up the phone, spend five minutes on the basics, because they occasionally solve the problem and they always give the technician better information.
- Confirm the thermostat is set to heat, the temperature setting is above the room temperature, and the batteries are fresh if the model uses them
- Check that the furnace switch, which looks like an ordinary light switch near the unit, is on
- Look at the breaker panel for a tripped breaker
- Inspect the air filter, since a clogged filter restricts airflow and can cause the furnace to overheat and shut itself down
If those items are fine and the furnace still will not heat, stop there. Opening the cabinet on a gas furnace is a job for a trained technician, because combustion, gas valves and high-voltage components all sit behind that panel.
What usually fails when a furnace stops heating
Most furnace repair calls in Orem come down to a short list of parts, and each one produces a recognizable symptom.
A dirty flame sensor. After the burners light, a thin metal rod called the flame sensor confirms that a flame is present. When soot or corrosion coats the rod, the control board loses that signal and shuts the gas off within seconds. The result is a furnace that lights, runs briefly and quits, then repeats the cycle.
A failed ignitor. Many modern furnaces use a hot surface ignitor, a ceramic element that glows to light the gas. Ignitors crack over time, and a cracked one may glow dimly or not at all. You will hear the inducer fan start, and then nothing happens.
A weak blower motor or capacitor. The blower pushes warm air through the ducts. If the motor struggles, the furnace may heat the exchanger but deliver little warm air to the rooms, or it may shut down on its high-limit switch because the heat has nowhere to go.
A stuck pressure switch or inducer problem. These parts prove that the exhaust path is clear before the burners ignite. When one fails, the furnace may attempt to start and then lock out.
A control board fault. The board coordinates every step. When it fails, the symptoms vary, which is why diagnosis matters more than guessing.
Need help narrowing it down? Call Valley Plumbing, Heating, and Cooling at (801) 341-4222 and describe what the furnace is doing.
Furnace repair in Orem and the problems cold weather exposes
A furnace that has been idle since last winter often fails on the first cold night, because that is the first time the system has to work hard in months. Dust burns off the heat exchanger and the smell can be alarming, but it usually fades quickly. A smell that does not fade, a burning smell that persists, or any rotten-egg odor is different. Gas has a deliberate additive so you can detect a leak, and if you notice it, leave the house and call your gas utility from outside.
Carbon monoxide deserves the same respect. A cracked heat exchanger or a blocked vent can allow combustion gases into the home. Working carbon monoxide detectors on every level are the safeguard, and the EPA explains the risks in its guide to carbon monoxide and indoor air quality. If an alarm sounds, get everyone outside, then call for help.
When a repair makes sense and when to talk about replacement
Technicians usually weigh three things. First, how serious is the failed part and how common is the failure on that model. Second, how old is the furnace, since an aging system tends to fail again in a different place. Third, what else did the inspection find, such as corrosion, a cracked exchanger or repeated board failures.
A single worn part on an otherwise healthy furnace is a good candidate for repair. A furnace with a cracked heat exchanger is a safety issue that generally ends the conversation about repair. In the middle are older units where a repair buys a season or two, and the honest advice may be to plan a replacement rather than keep patching. If you reach that point, the furnace installation page explains how Valley approaches a new system.
Keep the next breakdown from happening
A little maintenance prevents many of these calls. Replace the filter on the schedule the manufacturer recommends, keep the area around the furnace clear, and make sure supply and return vents are not blocked by furniture or rugs. A yearly tune-up lets a technician clean the flame sensor, test the ignitor and inspect the heat exchanger before winter does it for you. You can read about furnace maintenance on the Valley site.
Reaching a technician for furnace repair in Orem
If the furnace is not heating and the simple checks did not help, call Valley Plumbing, Heating, and Cooling at (801) 341-4222. Tell the dispatcher what the furnace is doing, how old it is and whether anything changed before it stopped. The more specific the description, the better prepared the technician will be when they arrive. You can also learn more about the team's local work on the Orem heating page.
